Complete Reset for Epson L312: Service Required / E11 Resolved

Complete Reset for Epson L312: Service Required / E11 Resolved

A full waste ink counter causes E11 on Epson L312. Reset via WicReset Connect in ~2 minutes. Keys from 6 EUR. Works on Windows 7–11 over USB.

🔑 Buy Reset Key ⬇️ Download WicReset Connect

When Epson L312 Needs Reset – Symptoms

  • Printer refuses to print, LEDs flashing.
  • Shows Error E11 or Service required.
  • Displays warning: Ink Pad Needs Service.

Why Epson L312 stops

A built-in waste ink counter governs service locks on Epson L312. On limit, the printer halts. Resetting that counter typically clears the warning without requiring pad replacement.

Quick facts – Epson L312 reset

ModelErrorSolutionOSReset time
Epson L312Error E11 / Ink Pad Needs ServiceWicReset ConnectWindows 7–11 (USB only)~2 minutes

Download reset tool & driver

⬇️ Download WicReset Connect

No verified official Epson driver found for Epson L312. Please refer to Epson Setup Navi for compatible software.

Video tutorial

▶ Watch WicReset tutorial

Available in many languages with narration.

Reset steps for Epson L312

  1. Connect Epson L312 to your PC via USB cable.
  2. Launch WicReset Connect and ensure the printer is detected.
  3. Buy a reset key, input it, and click Reset.
  4. Wait ~2 minutes, then turn the printer off and on again.
🔑 Buy Reset Key ⬇️ Download WicReset Connect

FAQ – Epson L312

Why blocked if pads aren’t full?

The counter is an estimate; it can lock before physical saturation.

Does resetting change ink levels?

No — it affects only the waste ink counter.

Can I reset over a USB hub?

Use a direct, high-quality USB cable for best stability.

Will I lose settings?

No — network/print settings remain.

Can I print immediately after reset?

Yes — power-cycle the printer and it’s ready.

Tips for Epson L312 reset

  • Reset around ~95% to avoid full lock.
  • Reduce unnecessary head cleanings.
  • Use a short, high-quality USB cable for stability.
🔑 Buy Reset Key ⬇️ Download WicReset Connect

This page is dedicated to Epson L312 reset instructions using WicReset Connect.

What you need

  • WicReset Connect key (only about €6 – the cheapest option)
  • Windows PC
  • USB cable

Time required

About 2 minutes

Difficulty

Very easy

Works for errors

  • Epson: E10, E11, E12, E91 and similar service errors
  • Canon: 1700, 5800 and similar waste ink / support code errors
  • Messages like “Waste ink counter full”, “Ink pad at the end of its service life”

Supported printer series

Epson: Artisan, B / BX, C / CX, D / DX, EP / EW, EcoTank (ET), K, L-series, M / ME, N / NX, P / PX / PM, Photo, R / RX, S / SC / SX, T / TX, WorkForce / WF and many other popular series.

Reset Epson ink pad service

If your Epson shows messages like “Ink pad is at the end of its service life”, “Ink pad service required” or “Waste ink pad full”, you can reset the Epson ink pad service using a WicReset Connect key. The program resets the internal waste ink counter, so the printer works again without visiting a service center.

  • Fixes “Epson ink pad service” / “Service required” warnings in a few minutes.
  • Works as a reset Epson ink pad service solution for most EcoTank, L-series, ET-series, XP, WF and Stylus printers.
  • No hardware resetter needed – only a Windows PC, USB cable and WicReset Connect.

FAQ (short)

Q: Do I need to replace the physical ink pad?
A: In most home and office cases you only reset the waste ink counter with WicReset Connect and keep using the printer normally.

Q: Is this a one-time reset?
A: Each key resets the counter once. You can repeat the procedure in the future with another key if the message appears again.