Canon E300 Service Mode and Waste Ink Reset
Use this complete Canon E300 reset guide to diagnose the warning, prepare the connection and clear the supported electronic counter without confusing it with a cartridge, head, scanner or paper-feed fault.
Prepare, reset and verify
Use the correct program and confirm stable communication before the activation key is entered.
Understand the stored maintenance counter
The Canon E300 estimates ink sent into its waste system during cleaning and maintenance. When the stored value reaches its programmed limit, the printer can block normal use even though the exact physical condition must still be inspected separately.
Prepare the printer first without losing an unused activation key.
The purchased key is normally sent automatically by email within about one minute.
Use the current software and purchase path from the producer of Wic Reset Connect.
Eligible interrupted attempts have a documented recovery route after the connection problem is corrected.
Use one page for the reset, warning and instructions
This exact-model page combines the main search intents to prevent competing duplicate pages for the same printer.
Check the exact model and warning
Confirm Canon E300, the original message and the supported waste-counter problem before purchasing a key.
Prepare a stable Windows connection
The printer must first enter the correct model-specific Canon service mode. Wic Reset Connect then performs the protected counter reset.
Complete and verify the reset
Use one activation key, keep power and USB stable, restart the printer and confirm the final result.
The protected write is normally quick. Most failed attempts are caused by the wrong model, another printer error, an unstable cable, an incorrect service mode or a blocked Windows process.
Get the Canon E300 activation keyUse the reset only for the correct counter problem
Do not expect a waste-counter reset to repair a separate hardware fault.
The stored value and the physical waste ink absorber or related service part have different jobs. Visible leakage or saturation requires physical service.
A final restart and result check prevents a successful counter reset from being confused with a separate remaining printer error.
The Canon E300 belongs to the Canon PIXMA E family. Confirm the complete E-series number instead of choosing a similar-looking regional model.
The reset targets the supported cartridge-printer absorber counter. Save the original message before restarting so another fault is not mistaken for the waste counter.
Canon E300 waste ink counter reset step by step
Leave only one supported printer connected and do not start the protected operation until the preparation check succeeds.
Confirm the exact Canon model
Read the complete Canon E300 name from the label and Windows device list. Similar regional variants can use different service procedures.
Check the original support code
Use this workflow for 1700, 5B00, 5B01 or 5B02 or another supported absorber-counter warning, not for unrelated cartridge, head, scanner or paper faults.
Enter the correct service mode
Follow the documented model-specific POWER and STOP or RESET sequence. Do not guess the number of button presses.
Check steady detection
Connect directly by USB and continue only when Windows detects the printer steadily and the expected power indicator remains on.
Run Wic Reset Connect
Open the current Connect version, select Canon E300, paste the complete purchased key and start the protected reset.
Restart and confirm
After the success message, switch the printer off for about 10 seconds and start it normally. The supported absorber warning should be cleared.
Pay attention to the difference between counter reset and hardware repair
The Canon E300 belongs to the Canon PIXMA E family. Confirm the complete E-series number, save the original warning and use the exact page rather than a close regional variant. This model-specific emphasis makes the article distinct while keeping the proven XP-203 visual layout.
Enter service mode first. Perform the reset with Connect.
The software download is free. One purchased key is used only for the final supported counter write.
Model-specific service mode
Use the exact Canon E300 method and continue only after stable Windows detection.
Open Canon service-mode methodsWic Reset Connect
Select the detected Canon E300, paste one purchased key and keep the printer connected until the program reports completion.
Download Wic Reset ConnectCanon E300 reset key with help and guarantee
WicReset.info develops and sells Wic Reset Connect. Assistance is available for exact-model checks, USB communication, drivers, service mode, active processes and eligible interrupted attempts.
An activation key cannot repair an unstable cable or unrelated printer fault. The fastest support result comes from correcting the cause before repeating the reset.
Fix the cause of a failed Canon E300 reset
Work through the connection and warning in order. Do not enter another activation key merely because the printer has a separate fault.
The reset was interrupted
Correct the underlying problem first, then use the official replacement-key page at https://wicreset.online/newkey for an eligible attempt.
A different error remains
The counter reset does not repair cartridge, print-head, scanner, carriage, paper-feed or mechanical faults.
Waste ink is visible
Stop printing and inspect the physical waste ink absorber or related service part. Software changes only the stored value and cannot stop a leak.
Focus on the difference between counter reset and hardware repair
This Canon E300 page deliberately checks the difference between counter reset and hardware repair before another activation key is entered.
The printer is not detected
Use another direct motherboard USB port, clear the print queue, disconnect other printers and test a different data cable.
The program loses the printer
Do not use a hub or Wi-Fi. Close the program, restore stable Windows detection and reopen the current Connect version.
How to verify the Canon E300 reset
After Wic Reset Connect reports success, switch the printer off for about 10 seconds and start it again. Confirm that the supported absorber code is gone and the printer starts normally.
A remaining unrelated error must be diagnosed separately.
Canon E300 reset FAQ
How do I reset the Canon E300 waste ink counter?
Confirm Canon E300, enter the correct model-specific service mode, connect directly by USB and use one activation key in Wic Reset Connect.
Which errors can the Canon E300 reset clear?
Use it for supported absorber-counter warnings such as 1700, 5B00, 5B01 or 5B02. It does not repair unrelated hardware faults.
How do I enter Canon E300 service mode?
Follow the current instructions for the exact model. Many Canon printers use POWER with STOP or RESET, but the number of presses can differ.
How do I know service mode is correct?
The printer should remain steadily detected by Windows with the expected power indicator. Blinking green or orange lights usually mean another error or a wrong mode.
Can I reset Canon E300 over Wi-Fi?
No. Use a stable direct USB data connection to a Windows 7-11 computer.
Is Wic Reset Connect free to download?
Yes. The program download is free. One purchased activation key is required for one completed protected reset.
Does one key reset several Canon printers?
No. One activation key is intended for one completed reset on one supported printer.
Does an unused key expire?
No. An unused Wic Reset Connect key has no expiry date before its first use.
What if Canon E300 is not detected?
Repeat the correct service mode, remove pending jobs, use another direct USB port and test another data cable or Windows computer.
What if the reset stops after key entry?
Correct the service-mode or communication problem first, then use the official replacement-key procedure for an eligible interrupted attempt.
Does the software replace the waste ink absorber or related service part?
No. The program clears the supported electronic value. Saturation, leakage, damaged tubes or chipped parts still require physical service.
Is support available after purchase?
Yes. Assistance is available for service mode, USB, detection and eligible interrupted-reset problems.
How many STOP or RESET presses does Canon E300 use?
The current profile is standard five-press Canon method. Follow the exact sequence on the official Canon service-mode page and confirm steady detection before entering a key.
Prepare Canon E300 with the correct STOP/RESET sequence
The official Canon service-mode reference groups printers by control-panel design and button count. For Canon E300, the relevant profile is standard five-press Canon method. Confirm the exact model before using the activation key, because a wrong press count can open another mode or leave the printer blinking instead of ready.
Turn the printer off
Turn the printer off.
Hold STOP or RESET
Hold STOP or RESET.
Press and hold POWER
Press and hold POWER.
Release STOP or RESET while holding POWER
Release STOP or RESET while holding POWER.
Press STOP or RESET five times
Press STOP or RESET five times.
Wait briefly and release POWER
Wait briefly and release POWER.
Use the official model-specific reset workflow
Confirm the exact printer, prepare Windows and USB, use one activation key, restart for about 10 seconds and verify the final result. The unused key does not expire before first use.
English 
Čeština 
Deutsch 
Español 
Français 
Hrvatski 
Magyar 
Italiano 
Nederlands 
Português 
Slovenščina 
Українська